Article
  • Improvement of Antistatic Performance of PET by Using Block Copolymer : Influencd of Molecular Weight of Poly(ethylene glycol) on the Thermal Properties and Moisture Absorptivity of PET-PEG Multi-Block Copolymer
  • Cho CG, Woo SW, Choi KL, Kim JH
  • 블록 공중합체를 이용한 PET-PEG 다중 블록공중합체의 열적성질과 흡습성
  • 조창기, 우상원, 최경림, 황승식
Abstract
Poly(ethylene terephthalate) (PET) was modified by incorporating poly(ethyl- one glycol) (PEG) moiety in its polymer chain and the hydrophilicity of the resultant copolymer films were estimated by the water contanct angle measurement. The copolymers contained PEG units with different molecular weights and different compositions. Thermal analysis revealed that PEG in the copolymer stayed as separated phases when Mn of PEG was higher than 1000. Separated phases were observed by scanning electron microscope when the Mn of PEG was 10000 or higher. Water contact angles were decreased as the Mn or content of PEG increased. Moisture regain was also increased as the Mn of PEG increased.

PET의 흡습성 및 제전성을 보완하기 위해 PEG를 사용하여 PET-PEG 다중 블록공중합체를 합성하였다. 이들 공중합체는 PEG의 분자량 증가에 따른 상분리 현상과 이에 따른 친수성의 증가가 정성적으로 검토되었다. 열분석에 의하면 PEG의 수평균 분자량이 1000 이상 되는 것을 사용하였을 경우 PET와 PEG가 공중합체 내에서 서로 어느 정도의 상분리를 하고 있다는 것을 알 수 있었고 PEG의 분자량이 10000 이상일 경우 상분리가 아주 현저하게 진행되어, 전자주사현미경으로 상분리된 상태를 관찰할 수 있었다. 제전성의 증가를 알아보기 위한 간접적인 방법으로 필름의 친수성을 측정하였다. 접촉각과 수분율을 측정해 PEG의 함량과 분자량이 증가할수록 친수성이 증가함을 알 수 있었으며, 낮은 분자량의 PEG를 많은 함량 사용하는 것보다는 약간 높은 분자량의 PEG를 소량 사용하는 편이 PET 표면의 흡습성을 증가시킬 수 있음을 알 수 있었다.

Keywords: poly(ethylene terephthalate); poly(ethylene glycol); block; copolymer; hydrophilicity; water contact angle; surface energy

  • Polymer(Korea) 폴리머
  • Frequency : Bimonthly(odd)
    ISSN 0379-153X(Print)
    ISSN 2234-8077(Online)
    Abbr. Polym. Korea
  • 2022 Impact Factor : 0.4
  • Indexed in SCIE

This Article

  • 1997; 21(5): 821-829

    Published online Sep 25, 1997

  • 10.7317/pk.
  • Received on Nov 30, -0001
  • Revised on Nov 30, -0001
  • Accepted on Nov 30, -0001

Correspondence to

  • E-mail: