Article
  • Preparation and Properties of Antimicrobial Zinc Alginate Films according to Solution Concentration
  • Lee JH, Seo HJ, Son TW, Lim HS
  • 용액 농도에 따른 항균성 알긴산 아연 필름의 제조 및 그 특성
  • 이주현, 서혜진, 손태원, 임학상
Abstract
Zinc alginate films were prepared by a film maker from sodium alginate solutions of different weight ratios and then they solidified into 3 wt% content ZnCl2 coagulation solution and washed and dried at a 60 ℃ oven for 20 min. The characteristics were measured by several methods (antimicrobial activity, viscosity, FTIR, TGA, SEM, EDS, contact angle, tensile strength and solubility) and the film properties were investigated. The antimicrobial test showed that the zinc alginate films result in excellent antimicrobial activity in the two strains (Klebsiella pneumonia, Staphylococcus). The surface of zinc alginate film from the solution of 9 wt% sodium alginate showed more uniform shape than any other films and the cross-section were hard and rough when the films were well-solidified by the ZnCl2 solution. The tensile strength of zinc alginate films increased along with the concentration of sodium alginate solution due to the cross-linking, and the initial thermal decomposition temperature increased gradually.

Alginate를 농도 별로 용액상태로 제조한 후 필름 메이커를 이용하여 필름 형태로 만든 후 3 wt%의 ZnCl2 수용액에 필름을 고화시킨 후 수세하여 60 ℃의 건조기에서 약 20분 동안 건조시켜 zinc alginate 필름을 제조하였다. 필름의 특성을 조사하기 위하여 항균성 및 점도와 FTIR, TGA, SEM, EDS 및 접촉각, 인장측정, 용해도분석 등을 측정하였다. 항균성 시험 결과, zinc alginate 필름에서는 두 균주(포도상구균, 폐렴간균) 모두 우수한 항균력이 나타나는 것을 확인하였다. 9 wt%의 sodium alginate로 제조한 zinc alginate 필름의 표면은 다른 농도별 필름보다 균일한 형태를 나타내었으며, ZnCl2 응고액에 잘 고화될 때 단단하고 거친 느낌의 단면 형태를 확인하였다. Zinc alginate 필름의 인장강도는 가교결합에 의해 sodium alginate 용액의 농도가 증가함에 따라 증가하였으며, 초기 열 분해 온도가 점차적으로 높아지고 있는 형태를 보였다.

Keywords: zinc alginate films; sodium alginate; solution concentration; antimicrobial activity.

  • Polymer(Korea) 폴리머
  • Frequency : Bimonthly(odd)
    ISSN 0379-153X(Print)
    ISSN 2234-8077(Online)
    Abbr. Polym. Korea
  • 2022 Impact Factor : 0.4
  • Indexed in SCIE

This Article

  • 2013; 37(6): 677-684

    Published online Nov 25, 2013

  • 10.7317/pk.
  • Received on May 6, 2013
  • Revised on Nov 30, -0001
  • Accepted on Jul 10, 2013

Correspondence to

  • E-mail: